Edwards 6537 Wiring Diagram

Edwards 6537 wiring diagram. The call may be reset at the initiating switch. To connect the horn and strobe to different circuits, loosen the terminals, remove the two wires and cap off with wire nuts. Wires, cords & cables wiring devices wiring devices & connectivity hvac supplies & equipment Route the extended wires to the horn/strobe and transformer (polarity is not important).

6537 pull cord switch (figures 1 and 2). It is equipped with a grounding wire and is suitable for installation in both plastic and metal boxes. The edwards 592 transformer is used to power the horn/strobe. The call may be reset at the initiating switch.

Signature data circuit wire length • b.5 24 vdc nac wire length • b.12 25 or 70 vrms nac wire length • b.15 addressable analog circuit wire length • b.17 cabinet battery • b.18 sac bus power • b.19 cpu memory • b.24 fiber optic cable worksheet • b.26 appendix c listing requirements • c.1 nfpa standards • c.2 It has a stainless steel face plate with a dpst switch. Extend the black and white wires using 18 awg wire and connectors (not supplied). Notes • refer to the signature loop controller installation sheet for slc wiring.

Secure it using two screws (supplied). The horn and strobe are connected together at the factory. Mount the horn/strobe onto the electrical box. Designed for either flush or surface mounting.

387478.cdr rev 2.0 page 2 of 2 installation b c install the inner door. Install a single gang 2 x 4 (51 mm x 102 mm) electrical box using suitable hardware. Verify that all field wiring is free of opens, shorts, and ground faults. It is equipped with a grounding wire and is suitable for installation in both plastic and metal boxes.

Signature data circuit wire length • b.5 notification appliance circuit calculations • b.11 25 or 70 vrms nac wire length • b.17 addressable analog circuit wire length • b.19 cabinet battery • b.20 sac bus power • b.21 cpu memory • b.26 fiber optic cable worksheet • b.28 appendix c listing requirements • c.1 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. Designed for either flush or surface mounting. It has a stainless steel face plate with a dpst switch.

Indoor fan starts on the selected speed. (about 6 mm) from the ends of all wires that connect to the terminal block of the module. Make all wiring connections as shown in figure 2. Connect the horn/strobe wire leads and terminals (figure 2).

Specifi cations are subject to change without notice. 4) make all wiring connections as shown in the diagram. 3) verify that all field wiring is free of opens, shorts, and ground faults. Install a single gang 2 x 4 (51 mm x 102 mm) electrical box using suitable hardware.

The edwards 592 transformer is used to power the horn/strobe. Wiring lights in parallel with one switch diagram how to wire within how to wire a pull cord light switch diagram, image size 500 x 500 px, and to view image details please click the image. 6537 pull cord switch the 6537 pull cord station provides emergency call activation and reset. Any queries please contact jemena compliance officer on 1300 855 824

All points along the cord are similar and linked. When a circuit checks out properly, connect it to the appropriate terminals as shown in the diagram on the next page. 6537 pull cord switch the 6537 pull cord station provides emergency call activation and reset. A typical cooling cycle of the heat pump 1.

Before connecting the field wiring, test the field wiring for opens or shorts. Ganging (multiple section pots.).1 cup maximum. The edwards 592 transformer is used to power the horn/strobe. The edwards 6537 pull cord switch provides features and specifications emergency call activation.

It has a stainless steel face plate with a dpst switch. Refer to figure 1 for item numbers in brackets in the following descriptions. It is equipped with a grounding wire and is suitable for installation in both plastic and metal boxes. Run a wire connected to earth ground through a

6537 pull cord switch the 6537 pull cord station provides emergency call activation and reset. For surface mounting, use a wiremold surface box. The edwards 6537 pull cord switch provides emergency call activation. For more information, consult wiring diagrams on page 4.

Cords are replaceable with a standard nylon cord. Tolerance, linearity tolerance, wiring diagram, and date code. The edwards rv rotary vane pump is shown in figure 1. Author u8ol0 posted on june 17, 2013 january 13, 2014 categories edwards/est, johnson controls edwards/est notification appliances edwards_892 series fire.

Cords are replaceable with a standard nylon cord. 6537 pull cord switch (figures 1 and 2). The edwards 6537 pull cord switch provides emergency call activation. Extend the black and white wires using 18 awg wire and connectors (not supplied).